data sheet these thermocouples are convenient for measuring a wide range of temperature in general plants, and are availble in j, e and k type. they are insulated with a porcelain tube, and then housed in a metal protecting tube for heat-, pressure-and corrosion-proofng. applicable standard: jis c 16021995 thermocouple element: material; negative lead alloy mainly made from copper and nickel alloy mainly made from copper and nickel alloy mainly made from nickel material positive lead steel alloy mainly made from nickel and chrome alloy mainly made from nickel and chrome j e k symbol note: positive lead means the one connected to positive terminal of the instrument measuring thermoelectromotive force, and nega - tive lead means the one connected to the opposite terminal. class; note: class3 is applicable only to low tem- peratures below 40c. temperature accuracy; diameter of element; 1, 3.2 normal limit and allowable overheat limit; symbol diameter of element [mm] normal limit [c] allowable overheat limit [c] j 1 450 550 3.2 600 750 e 1 500 550 3.2 700 800 k 1 750 950 3.2 1000 1200 note: the normal limit means the temperature limit up to which the thermocouple can be used continu - ously in air. allowable overheat limit means the temperature limit up to which the thermocouple can be used for a short time, when necessary. material of protecting tube: s ; 304 stainless steel r ; 310s stain- less steel w ; 316 stainless steel u ; 27cr *t ; 316l stainless steel j ; 20cr-80ni mounting and protecting tube form: note: the thermocouple of diameter 27 in protecting tube form is applicable to the case where material of protecting tube is j or u. in the case of u, and with mounting form d and q, the double element is applicable. class symbol of material 1 j, e, k 2 j, e, k 3 e, k j,e,k type thermocouples for general use fta,b,d specifications protecting tube form mounting form insertion type screw-in type screw-in type flange type a d f ? j ? m q symbol k tolerance class measured temperature (?c) -40?c or more, less than +375?c 1 1.5?c tolerance means the maximum allowable limit of the value calculated by subtracting the temperature of the temperature measuring junction from the temperature obtained by converting the thermal electromotive force by the reference thermal electromotive force. |t| is the value indicated by temperature (?c) that is note: 375?c or more, less than 1000?c 0.004?|t| -40?c or more, less than +333?c 2 2.5?c 333?c or more, less than 1200?c 0.0075?|t| -167?c or more, less than +40?c 3 2.5?c -200?c or more, less than -167?c 0.015?|t| e -40?c or more, less than +375?c 1 1.5?c 375?c or more, less than 800?c 0.004?|t| -40?c or more, less than +333?c 2 2.5?c 333?c or more, less than 900?c 0.0075?|t| -167?c or more, less than +40?c 3 2.5?c -200?c or more, less than -167?c 0.015?|t| j -40?c or more, less than +375?c 1 1.5?c 375?c or more, less than 750?c 0.004?|t| -40?c or more, less than +333?c 2 2.5?c 333?c or more, less than 750?c 0.0075?|t| date EDS2-1G jan. 31, 2007
fta,b,d mounting method: insertion type; either movable fange (ftr), movable airtight fange (ftt), or movable airtight screw (fts) is employed for mounting. screw-in type; g3/4 (pf3/4) or r3/4 (pt3/4) external thread flange type; jis 10k-25a ? jis 20k-25a ? jis 30k-25a or jis 63k-25a composition: diameter of element protecting tube material (symbol) mounting method mounting form insertion type a insertion type d screw-in type f ? j flange type m flange type q movable fange or movable airtight fange jis 5k-25 ? 10k-25 movable airtight screw g3/4(pf3/4) movable fange or movable airtight fange jis 5k-25 ? 10k-25 movable airtight screw g1( pf1), g1 1 / 4 (pf1 1 / 4 ) welded screw g3/4 (pf3/4), r3/4 (pt3/4) welded fange jis 10k-25 jis 20k-25 jis 30k-25 jis 63k-25 welded fange jis 10k-25 jis 20k-25 s ? w ? t* s ? w ? t* r ? u ? j s ? w ? t* s ? w ? t* s ? w ? t* r ? u ? j 1 3.2 1 1 3.2 note: (1) on the j, e thermocouple of mounting method d, q, pro - tecting tube material is s, w, t. (2) on the thermocouple of mounting method d and protecting tube material j, movable airtight screw is pf1/4. insertion length: see other table (page 5) working conditions: see other table (pages 3 and 4) terminal box: material; diecast aluminum alloy conduit connection; g1/2 (pf1/2) coating; baked melamine resin finish color; silver standard thermoelectromotive force table: see other table (page 5) scope of delivery: thermocouple (1) combination of mounting form and protect - ing tube form (2) combination of protecting tube material and mounting method a d f j m q s w t r u j notes: (1) mark; manufacturing possible (2) mark; fta, ftd are applicalbe only to this material (3) mark; applicalbe to fexplo-sionproof- type note: the thermocouple of diameter 27 in protecting tube form is applicable to the case where material of protecting tube is j or u. in the case of u, and with mounting form d and q, the double element is applicable. code symbols 3 d t f - 3 b t f - 3 a t f a t f b t f d t f - 10 2 1 3 4 5 6 7 8 11 12 9 description 1 2 3 6 7 8 a d f j m q 0 1 5 3 9 5 a c f s w t r u j asterisked (*) items : non-standard * (1) * (2) * element single element double element single element double element single element double element (0.75 class) (0.75 class) (1.5 class) (1.5 class) (0.4 class) (0.4 class) ftd, ftb only mounting method insertion type insertion type screw-in type (for low temperature) screw-in type (for high temperature) flange type flange type protecting tube material 304 stainless steel 316 stainless steel 316l stainless steel 310s stainless steel 27cr 20cr-80ni 1 2 3 4 7 8 0 mounting dimension flange jis 10k-25a flange jis 20k-25a flange jis 30k-25 (only m type) flange jis 63k-25 (only m type) mounting screw g3/4 (pf3/4) mounting screw r3/4 (pt3/4) insertion type insertion length (according to table of insertion length) fill in insertion length in cm unit ex.: structure/explosionproofing standard type flameproof type (d2g4) intrinsically safe explosionproofing (i3ng5) for connection with zener barrier kind of thermocouple j thermocouple k thermocouple e thermocouple 500mm 050 1000mm 100 ? ? ? method material
working conditions working temp,; ?200 to +700 c working pressure; atmospheric pressure when both movable airtight screw and fange are used, working pressure can be up to 0.1mpa {1.02kgf/cm 2 } working temp,; ?200 to +500 c working pressure; atmospheric pressure when both movable airtight screw and fange are used, working pressure can be up to 0.1mpa {1.02kgf/cm 2 } working temp,; 0 to 450 c working pressure; below fange (jis) nominal pressure jis 10k-25 ? jis 20k-25 jis 30k-25 ? jis 63k-25 material; 304, 316, 316l stainless steel working temp,; 0 to 600 c working pressure; atmospheric pressure when both movable airtight screw and fange are used, working pressure can be up to 0.1mpa {1.02kgf/cm 2 } working temp,; 0 to 450 c working pressure; atmospheric pressure when both movable airtight screw and fange are used, working pressure can be up to 0.1mpa {1.02kgf/cm 2 } 1 2 7 8 fta s w t a 1 2 7 8 fta s w t 1 2 7 8 fta s w t f j 1 2 7 8 fta s w t 1 2 3 4 1 2 7 8 fta s w t 1 2 3 6 7 8 ftd s w t 1 2 3 6 7 8 d s w t 1 2 3 6 7 8 q s w t 1 2 3 6 7 8 m 1 2 3 4 s w t 1 2 ftd ftd ftd 1 2 3 6 7 8 s w t ftd a q m application used for corrosive gas or liquid, and when the insertion length is desired to be adjustable used for oxidizing atmosphere (gas), and when the insertion length is desired to be adjust - able used for corrosive gas or liquid, j type is used for comparatively high temp. working temp,; 0 to +600 c working pressure; below fange (jis) nominal pressure jis 10k-25 ? jis 20k-25 material; 304, 316, 316l stainless steel working temp,; ?200 to +500 c working pressure; below fange (jis) nominal pressure jis 10k-25 ? jis 20k-25 jis 30k-25 ? jis 63k-25 material; 304, 316, 316l stainless steel working temp,; ?200 to +700 ? c working pressure; below fange (jis) nominal pressure jis 10k-25 ? jis 20k-25 material; 304 stainless steel used for corrosive gas or liquid, and when airtightness is especially required used for oxidizing atmosphere (gas) used for corrosive gas or liquid, and when the insertion length is desired to be adjustable used for corrosive gas or liquid, j type is used for comparatively high temp. used for corrosive gas or liquid, and when airtightness is especially required used for oxidizing atmosphere (gas), and when airtightness is especially required mass{weight} 0.5 to 1.4 kg 1 to 6 kg 0.7 to 1.6 kg 1.4 to 2.3 kg (jis 10k) 1.4 to 2.3 kg (jis 20k) 2 to 2.9 kg (jis 30k) 2.9 to 3.8 kg (jis 63k) 2 to 7 kg used for oxidizing atmosphere (gas), and when the insertion length is desired to be adjust - able 0.5 to 1.4 kg 1 to 6 kg 0.7 to 1.6 kg 2 to 7 kg 1.4 to 2.3 kg (jis 10k) 1.4 to 2.3 kg (jis 20k) 2 to 2.9 kg (jis 30k) 2.9 to 3.8 kg (jis 63k) outline diagrams fig. 1 fig. 2 fig. 3 fig. 4 fig. 5 fig. 6 fig. 7 fig. 8 fig. 9 fig. 10 fig. 1 fig. 2 fig. 3 fig. 4 fig. 5 fig. 6 fig. 7 fig. 8 fig. 9 fig. 10 working temperature working pressure model ( ) ( ) ( ) ( ) 1 2 d f j 0 100 450 c 0 4 5 mp a fta. fj 100 500 c -200 0 4 mp a 5 ftd7. fj
fta,b,d s w t working temp.; C200 to +750 c working pressure; atmospheric pressure when both movable airtight screw and fange are used, working pressure can be up to 0.1mpa {1.02kgf/cm 2 } application used for corrosive gas or liquid, and when the insertion length is desired to be adjustable mass{weight} 0.5 to 1.4 kg outline diagrams fig. 1 model 1 2 3 6 7 8 a ftb 1 2 7 8 ftb d u 1 2 3 6 7 8 d s w t ftb 1 2 7 8 ftb d r 1 2 7 8 ftb d j 1 2 3 6 7 8 s w t ftb f j 1 2 7 8 ftb q r 1 2 3 6 7 8 s w t m ftb 1 2 3 4 1 2 3 6 7 8 s w t q ftb 1 2 1 2 7 8 ftb q u 1 2 1 2 1 2 7 8 ftb q j 1 2 working temp,; C200 to +900 c working pressure; atmospheric pressure when both movable airtight screw and fange are used, working pressure can be up to 0.1mpa {1.02kgf/cm 2 } working temp,; 0 to 1000 c working pressure; atmospheric pressure when both movable airtight screw and fange are used, working pressure can be up to 0.1mpa {1.02kgf/cm 2 } working temp,; 0 to 1000 c working pressure; atmospheric pressure when both movable airtight screw and fange are used, working pressure can be up to 0.1mpa {1.02kgf/cm 2 } working temp,; 0 to 1000 c working pressure; atmospheric pressure when both movable airtight screw and fange are used, working pressure can be up to 0.1mpa {1.02kgf/cm 2 } working temp,; C200 to +750 c working pressure; below fange (jis) nominal pressure jis 10k-25 ? jis 20k-25 jis 30k-25 ? jis 63k-25 material; 304, 316, 316l stainless steel working temp,; C200 to +900 c working pressure; below fange (jis) nominal pressure jis 10k-25 ? jis 20k-25 material; 304 stainless steel working temp,; 0 to 1000 c working pressure; below fange (jis) nominal pressure jis 10k-25 ? jis 20k-25 material; 304 stainless steel working temp,; 0 to 1000 c working pressure; below fange (jis) nominal pressure jis 10k-25 ? jis 20k-25 material; 304 stainless steel working temp,; 0 to 1000 c working pressure; below fange (jis) nominal pressure jis 10k-25 ? jis 20k-25 material; 304 stainless steel working temperature, working pressure used for oxidizing atmosphere (gas), and when the insertion length is desired to be adjust - able used for high temp. gas includ - ing sulfur gas and carbon gas used for high temp. gas exclud - gas excluding sulfur gas used when mechanical strength is required and for high temp. ing sulfur gas and carbon gas used for high temp. gas exclud - ing sulfur gas (gas) used for high temp. gas includ - and when airtightness is espe - cially required used for oxidizing atmosphere j type is used for comparatively high temp. used for corrosive gas or liquid, is required and for high temp. gas excluding sulfur gas used for corrosive gas or liquid, ing sulfur gas used when mechanical strength 1 to 6 kg fig. 2 0.7 to 1.6 kg fig. 3 fig. 4 1.4 to 2.3 kg (jis 10k) 1.4 to 2.3 kg (jis 20k) 2 to 2.9 kg (jis 30k) 2.9 to 3.8 kg (jis 63k) fig. 5 fig. 6 fig. 7 fig. 8 2 to 7 kg fig. 9 fig. 10 ( ) ( ) ( ) ( ) ( ) mp a -200 0 750 c 0.5 4 5 500 100 ftb7. fj
m 150 200 250 300 350 400 450 500 550 600 650 700 750 800 q 200 250 300 350 400 450 500 550 600 650 700 750 800 j 150 200 250 300 350 400 450 500 550 600 650 700 750 f 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 d 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 a 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 mounting method insertion length insertion length "l" insertion length "l" q 850 950 1050 1150 1250 1350 1450 1550 1650 1750 1850 2350 2850 3350 3850 m 850 950 1050 1150 1250 1350 j 800 900 1000 1100 1200 1300 f 900 1000 1100 1200 1300 1400 d 950 1050 1150 1250 1350 1450 1550 1650 1750 1850 1950 2450 2950 3450 3950 a 950 1050 1150 1250 1350 1450 mounting method insertion length insertion length [dimension "l" of "outline diagrams"] jis c 1602-1995 jis c 1602-1995 C100 0 0 100 200 300 400 500 600 700 800 C4633 0 0 5269 10779 16327 21848 27393 33102 39132 45494 404 501 507 545 555 554 552 560 587 623 647 C5037 C501 507 5814 11334 16881 22400 27953 33689 39755 46141 389 494 512 546 555 553 552 563 590 627 645 C5426 ?995 1019 6360 11889 17434 22952 28516 34279 40382 46786 375 487 518 549 556 552 552 564 594 630 645 C5801 ?1482 1537 6909 12445 17986 23504 29080 34873 41012 47431 358 479 522 550 555 552 553 567 597 633 643 C6159 ?1961 2059 7459 13000 18538 24057 29647 35470 41645 48074 341 470 526 551 555 552 553 569 601 636 641 C6500 C2431 2585 8010 13555 19090 24610 30216 36071 42281 48715 321 462 531 552 555 552 554 572 604 638 638 C6821 C2893 3116 8562 14110 19642 25164 30788 36675 42919 49353 302 451 534 553 555 552 556 574 609 640 636 C7123 C3344 3650 9115 14665 20194 25720 31362 37284 43559 4 9 989 280 442 537 554 554 551 556 577 612 644 633 C7403 C3786 4187 9669 15219 20745 26276 31939 37896 44203 50622 256 429 539 555 554 552 558 580 616 645 629 C7659 C4215 4726 10224 15773 21297 26834 32519 38512 44848 51251 231 418 543 555 554 551 559 583 620 646 626 C7890 C4633 5269 10779 16327 21848 27393 33102 39132 45494 51877 temp. [c] 0 C10 C20 C30 C40 C50 C60 C70 C80 C90 C100 temp. [c] 0 10 20 30 40 50 60 70 80 90 100 temp. [c] 0 10 20 30 40 50 60 70 80 90 100 remarks: thermoelectromotive force values shown in the above table are when temperature of reference junction is 0 c C100 0 0 100 200 300 400 500 600 700 800 900 ?5237 0 0 6319 13421 21036 28946 37005 45093 53112 61017 68787 444 582 591 679 743 781 801 810 807 796 784 767 ?5681 ?582 591 6998 14164 21817 29747 37815 45900 53908 61801 69554 426 570 601 687 748 783 803 809 805 795 782 765 ?6107 ?1152 1192 7685 14912 22600 30550 38624 46705 54703 62583 70319 409 557 609 694 752 786 804 810 804 794 781 763 ?6516 ?1709 1801 8379 15664 23386 31354 39434 47509 55497 63364 71082 391 546 619 702 756 788 805 809 804 792 780 762 ?6907 ?2255 2420 9081 16420 24174 32159 40243 48313 56289 64144 71844 372 532 628 708 761 790 806 810 803 791 778 759 ?7279 ?2787 3048 9789 17181 24964 32965 41053 49116 57080 64922 72603 353 519 637 714 764 793 807 809 801 790 776 757 ?7632 ?3306 3685 10503 17945 25757 33772 41862 49917 57870 65698 73360 331 505 645 721 768 795 807 809 801 789 775 755 ?7963 ?3811 4330 11224 18713 26552 34579 42671 50718 58659 66473 74115 310 491 655 727 771 796 808 808 799 787 773 754 ?8273 ?4302 4985 11951 19484 27348 35387 43479 51517 59446 67246 74869 288 475 663 733 775 798 809 806 798 786 771 752 ?8561 ?4777 5648 12684 20259 28146 36196 44285 52315 60232 68017 75621 264 460 671 737 777 800 809 808 797 785 770 752 ?8825 ?5237 6319 13421 21036 28946 37005 45093 53112 61017 68787 76373 temp. [c] 0 C10 C20 C30 C40 C50 C60 C70 C80 C90 C100 temp. [c] 0 10 20 30 40 50 60 70 80 90 100 temp. [c] 0 10 20 30 40 50 60 70 80 90 100 standard thermoelectromotive force of j thermocouple (unit: v) standard thermoelectromotive force of e thermocouple (unit: v) remarks: thermoelectromotive force values shown in the above table are when temperature of reference junction is 0 c
fta,b,d standard thermoelectromotive force of k thermocouple (unit: v) temp. [c] 0 C10 C20 C30 C40 C50 C60 C70 C80 C90 C100 temp. [c] 0 10 20 30 40 50 60 70 80 90 100 jis c 1602-1995 temp. [c] 0 10 20 30 40 50 60 70 80 90 100 C100 ?3554 298 ?3852 286 ?4138 273 ?4411 258 ?4669 244 ?4913 228 ?5141 213 ?5354 196 ?5550 180 ?5730 161 ?5891 0 0 392 ?392 386 ?778 378 ?1156 371 ?1527 362 ?1889 354 ?2243 344 ?2587 333 ?2920 323 ?3243 311 ?3554 0 0 397 397 401 798 405 1203 409 1612 411 2023 413 2436 415 2851 416 3267 415 3682 414 4096 100 4096 413 4509 411 4920 408 5328 407 5735 403 6138 402 6540 401 6941 399 7340 399 7739 399 8138 200 8138 401 8539 401 8940 403 9343 404 9747 406 10153 408 10561 410 10971 411 11382 413 11795 414 12209 300 12209 415 12624 416 13040 417 13457 417 13874 419 14293 420 14713 420 15133 421 15554 421 15975 422 16397 400 16397 423 16820 423 17243 424 17667 424 18091 425 18516 425 18941 425 19366 426 19792 426 20218 426 20644 500 20644 427 21071 426 21497 427 21924 426 22350 426 22776 427 23203 426 23629 426 24055 425 24480 425 24905 600 24905 425 25330 425 25755 424 26179 423 26602 423 27025 422 27447 422 27869 420 28289 421 28710 419 29129 700 29129 419 29548 417 29965 417 30382 416 30798 415 31213 415 31628 413 32041 412 32453 412 32865 410 33275 800 33275 410 33685 408 34093 408 34501 407 34908 405 35313 405 35718 403 36121 403 36524 401 36925 401 37326 900 37326 399 37725 399 38124 398 38522 396 38918 396 39314 394 39708 393 40101 393 40494 391 40885 391 41276 1000 41276 389 41665 388 42053 387 42440 386 42826 385 43211 384 43595 383 43978 381 44359 381 44740 379 45119 1100 45119 378 45497 376 45873 376 46249 374 46623 372 46995 372 47367 370 47737 368 48105 368 48473 365 48838 1200 48838 364 49202 363 49565 361 49926 360 50286 358 50644 356 51000 355 51355 353 51708 352 52060 350 52410 1300 52410 349 52759 347 53106 345 53451 344 53795 343 54138 341 54479 340 54819 remarks: thermoelectromotive force values shown in the above table are when the temperature of reference junction is 0 c a b d ft a f s w t a 1 2 3 6 7 8 03 - ??? a b d ft d 1 2 3 6 7 8 a f 03 - ??? s, r w , j t u note: d is as follows: protecting tube material element d single and double 304, 22 316, 316l stainless steel single 27cr 21.3 double 27cr 27 single and double 20cr-80ni 27 fig. 1 determine insertion length "l" by collating the 5th digit of code symbols with the table shown on page 5. for example, when the 5th digit of code symbol is a, select "l" from 150mm to 1450mm (twenty two varieties) by the table shown on page 5. insertion type fig. 2 outline diagram [unit:mm] (refer to working conditions of page 3)
screw-in type flange type note: dimension "a" in case of screw-in type dimension "a" for low temp. for high temp. 150mm 50mm fig. 5 a b d ft fig. 6 a b d ft fig. 7 a b d ft 1 2 3 6 7 8 a f s w t 23 - ??? m m 1 2 3 6 7 8 a f s w t 13 - ??? m 1 2 3 6 7 8 a f s w t 43 - ??? fig. 3 a b d ft fig. 4 a b d ft 1 2 3 6 7 8 f j a f s w t 83 - ??? 1 2 3 6 7 8 f j a f s w t 73 - ???
fta,b,d protecting tube diameter of fig. 9, 10 protecting tube material 304, 316, 316l stainless steel 27cr 20cr-80ni single double single double single double element 21.3 27 d 27 22 d 1 34 29 29 terminal box for fameproof type movable airtight screw (type fts) 2, 4, 6 in 4th digit of code 1, 3, 5 in 4th digit of code fig. 8 a b d ft m 1 2 3 6 7 8 a f s w t 33 - ??? a b d ft q 1 2 3 6 7 8 a f 13 - ??? s, r w , j t u fig. 9 a b d ft q 1 2 3 6 7 8 a f 23 - ??? fig. 10 s, u w , r t j mass {weight} [kg] protecting tube outer dia. ( d) type d 1 approx. ? fts6e fts6d fts4c fts2a 31 28 24 13 r1 1/4 (pt1 1/4) r3/4 (pt3/4) d 2 r1 (pt1) r1 1/4 (pt1 1/4) a 58 58 50 38 b 30 30 20 20 100 100 80 80 30 25 to 27 21.3 to 22 12 1.2 1.2 0.8 0.8 note: material is ss400 mass {weight} [kg] type d 1 fts5e fts5d fts3c fts1a 31 28 24 13 g1 1/4 (pf1 1/4) g3/4 (pf3/4) d 2 g1 (pf1) g1 1/4 (pf1 1/4) a 69 69 59 48 b 58 58 50 38 30 25 to 27 21.3 to 22 12 1.2 1.2 0.8 0.8 note: material is ss400 approx. ? 100 100 80 80 c 30 30 20 20 protecting tube outer dia. ( d) 100 125 cap g1/2 (pf1/2)
movable airtight fange (type ftt) jis 10k-50 fange jis 10k-25 fange jis 5k-25 fange movable fange (type ftr) jis 10k-50 fange jis 5k-25 fange jis 10k-25 fange 31 28 24 d 30 26.8 ? 27 21.3 ? 21.7 ? 22 ss400 material protecting tube outer dia. ( d) 28 24 13 d 26.8 ? 27 21.3 ? 21.7 ? 22 12 fc200 material protecting tube outer dia. ( d) ftt2d ftt2c ftt2a type 28 24 13 d 26.8 ? 27 21.3 ? 21.7 ? 22 12 fc200 material protecting tube outer dia. ( d) ftt1d ftt1c ftt1a type 50 31 28 24 13 d 49 30 25 to 27 21.3 to 22 12 ss400 material protecting tube outer dia. ( d) 28 24 13 d 25 to 27 21.3 to 22 12 fc200 material protecting tube outer dia. ( d) ftr2d ftr2c ftr2a type 28 24 13 d 25 to 27 21.3 to 22 12 fc200 material protecting tube outer dia. ( d) ftr1d ftr1c ftr1a type
fta,b,d information in this catalog is subject to change without notice. printed in japan head office gate city ohsaki, east t ower , 11-2, osaki 1-chome, shinagawa-ku, t okyo 141-0032, japan http://www .fesys.co.jp/eng instrumentation div . international sales dept. no.1, fuji-machi, hino-city , t okyo, 191-8502 japan phone: 81-42-585-6201, 6202 fax: 81-42-585-6187 http://www .fic-net.jp/eng caution on safety *before using this product, be sure to read its instruction manual in advance.
|
